AddiWire

Additive manufacturing news and European prices, with independent expert commentary

Industrial AM

Raise3D stretches RMS220 SLS build height to 450 mm through a software update

Published 1 sourceSummary written with AIDeutsche Version

Raise3D is raising the build height of its RMS220 SLS printer from 350 to 450 mm, lifting nominal volume from 16.9 to 21.8 litres. The change arrives as a firmware and software update on 17 November. The company will show it at Formnext 2026 next to the B520 sandblaster, which ships from December.

Key facts
  • Build envelope grows to 220 × 220 × 450 mm, 16.9 to 21.8 litres
  • Free software update rolls out 17 November, no hardware changes
  • Raise3D estimates 25 to 30% more small-batch throughput
  • B520 sandblaster ships December 2026; Formnext Hall 12.1, Booth D21

Context SLS (selective laser sintering) fuses plastic powder with a laser, and the unfused powder around the parts supports them, so no support structures are needed and parts can be stacked at different heights.

What changes on the RMS220?

The build envelope grows to 220 × 220 × 450 mm, which adds 100 mm of Z height and lifts nominal volume by nearly 30%. Raise3D says the update needs no hardware work and is free for current owners of the printer. Raise3D showed a 450 mm automotive light cover printed in one piece in PA NEXT powder, which avoids a bonded joint and a visible seam.

How could the extra height affect throughput?

Because surrounding powder supports parts in SLS, small components can be nested at several heights, so more of a recurring order fits into one job. Fewer builds mean fewer setups and idle gaps, and preparation costs spread over more parts. Raise3D estimates a 25 to 30% throughput gain in typical small-batch scenarios, depending on nesting efficiency, added print time and how fast batches move through cooling, cleaning and finishing.

What happens after printing?

The RMS220 uses swappable Build Unit 220 chambers, so a finished build can cool outside the printer while a second unit starts the next job. The C220-P station then separates parts from loose powder and recovers powder for reuse within material limits. The B520 sandblaster handles the blasting step in programmed cycles with a removable basket, with recommended loads of 10 litres in the standard basket and 30 litres in the large one. Manual blasting and an optional polishing module are available. It debuts in Europe at Formnext and ships from December 2026.

Where can it be seen?

Raise3D exhibits the system at Formnext, 17 to 20 November 2026, in Hall 12.1, Booth D21.

What it means

For small and mid sized firms running SLS in house, a free update that adds build height changes the business case without new capital, but the gain exists only if parts nest well. The 25 to 30% figure is a vendor estimate for typical small batches, so it should be checked against a real order mix. Cooling, unpacking and blasting capacity may become the new bottleneck, and larger single parts need their own validation in the chosen powder. This continues Raise3D's earlier large-format FFF launch, now extended to powder.

Earlier on AddiWire

Frequently asked questions

How big is the RMS220 build volume after the update?

It becomes 220 × 220 × 450 mm, or 21.8 litres nominal, up from 16.9 litres. That is an increase of nearly 30%.

Does the upgrade cost anything?

Raise3D says the software and firmware update is free for existing RMS220 owners and needs no hardware changes. It rolls out on 17 November.

When does the B520 sandblaster ship?

Raise3D plans shipments from December 2026, after its European debut at Formnext in Frankfurt. It was first shown at RAPID + TCT in Boston in April.

Read the original reports
  1. TCT Magazine, 16 Nov 2026