AddiWire

Additive manufacturing news and European prices, with independent expert commentary

Materials

Hydra's ceramic printer mills away its own defects before firing

Published 1 sourceSummary written with AIDeutsche Version

Hydra Manufacturing, a University of Leeds spin-out, sells CHAMP, a ceramic paste printer with a built-in milling spindle and inspection that can cut out and redo a faulty layer. Its first machine went to Lucideon shortly after the company was founded. At Formnext 2026 Hydra will show alumina, tungsten carbide and hydroxyapatite samples and offers trials on customers' own materials.

Key facts
  • CHAMP combines paste deposition, infrared drying, machining and inspection in one ceramic printer
  • Reworked test specimens showed 68% lower void content in published CT scans
  • Binder removal and sintering take one furnace cycle of about 18 to 24 hours
  • Formnext stand: Hall 12.0, F139, with FastCast Ceramics talk on 17 November

Context Sintering is the furnace step that fuses ceramic particles into a dense solid after the binder has burned out, and the part shrinks while it does so.

How does the printer repair a defect?

CHAMP combines paste deposition, infrared drying, machining and inspection in one machine. A camera-based system, trained on thousands of hand-labelled images of too much or too little paste, flags a fault. If there is an excess, the spindle trims the layer back to the intended height. If material is missing, the machine removes that layer, reprints it and changes extrusion pressure to make a repeat less likely.

The Leeds research machine was tested with CT scans, and a paper in Additive Manufacturing reported 68% lower void content in reworked specimens than in uncorrected ones. That figure applies to those test specimens only, and a buyer still needs evidence for its own material, geometry and tolerance.

Why machine a ceramic inside the printer?

Cutting can be done while a surface is still reachable, then the build continues around it. Founder Louis Masters says complex shapes often cannot be machined fully at the end. He also estimates that grinding or machining of fired wear-resistant ceramics such as silicon carbide can make up as much as 80% of the finished cost in demanding cases. Before firing, the binder holds the body together weakly, so cutting is easier.

Hydra's software enlarges the starting geometry to account for shrinkage, adds stock for the cutter and adapts layer heights for drying shrinkage. Masters says behaviour is fairly repeatable with consistent feedstock, but the team is still validating how well fired parts hold tolerance across geometries.

Where does the time saving come from?

With its lower-binder feedstocks, Masters describes overnight drying followed by one furnace cycle for binder removal and sintering, about 18 hours or around 24 with cooling. He contrasts this with some light-cured ceramic builds that need five days for binder removal alone. He concedes that light-based processes are better for very fine features. Paste extrusion also suits dark ceramics that are hard to formulate for light curing.

Who is buying and what comes next?

Lucideon ordered a machine about a week after Hydra was incorporated, supplying match funding for a grant. Early demand has come mainly from defence and electronics rather than the aerospace, medical and energy sectors Hydra expected. Prospects can send their own material for trials and test coupons, and Hydra is exploring rentals. Its silicon carbide formulation was still in final qualification at the time of the interview. At Formnext, Hydra and FastCast Ceramics speak on porous casting ceramics on 17 November at 14:00 CET, Hall 12.0, Stand F139.

What it means

For manufacturers that already mix and fire their own ceramic, paste extrusion with in-process machining could shorten the route to a shape and cut grinding after the furnace. The business case depends on how much post-sinter finishing a part needs. Qualification remains open: fired tolerance across geometries is still being validated, and silicon carbide was not yet qualified. Trials on the buyer's own material are the practical way to test the claims.

Frequently asked questions

What is CHAMP?

CHAMP is Hydra Manufacturing's Ceramic Hybrid Additive Manufacturing Platform, which combines paste deposition, drying, machining and inspection in one machine.

Who bought the first machine?

Lucideon, a materials development company, ordered the first machine about a week after Hydra was incorporated, providing match funding for a grant.

Can customers test their own ceramic material?

Yes. Hydra runs trials on customer-supplied material, reports how the formulation behaves and makes test coupons with features from the customer's component. It is also exploring rentals.

Read the original reports
  1. 3D Printing Industry, 16 Nov 2026