AddiWire

Additive manufacturing news and European prices, with independent expert commentary

Events

Formnext day three: cheaper kit, wider buyer base and safety doubts over a desktop metal printer

Published 2 sourcesSummary written with AIDeutsche Version

A 3DPrint.com commentary from the third day of Formnext 2026 describes a busier show with more buyers and falling prices, including for post-processing equipment. The author highlights DWS hybrid SLA and Atlix's sale to BMW, but raises fire and powder safety concerns about SnowX's SnowPod desktop metal printer.

Key facts
  • DyeMansion Powershot Pro is quoted at $16,000 for entry-level depowdering and finishing
  • Atlix sold an xBUILD 5000 LPBF system to BMW for aluminium parts
  • One attendee counted 120 distinct releases and new products at Formnext
  • Author cites dust explosion risk at roughly 20 to 60 g/m³ in air

Context LPBF (laser powder bed fusion) melts metal powder layer by layer with a laser, which is why powder handling and fire safety matter for desktop versions.

Is the Formnext buyer base changing?

The author reports a very busy third day with visitors buying, learning and researching, and says hardware sales went better than last year. Buyers are described as more informed and the user base as broader, spanning desktop, mid-range and high-end shoppers. The share of visitors who buy something at the show is said to have risen.

Where are prices falling?

Resins and post-processing equipment are described as far cheaper than before, partly due to Chinese influence. DyeMansion, HP and Formlabs offer entry-level depowdering and surface finishing, and the DyeMansion Powershot Pro is quoted at $16,000. Cheaper vacuums, drop cams, filament and sieves are also mentioned. The author counts a growing ecosystem of peripheral vendors and notes a friend tallied 120 distinct releases and products at the show.

Which products stood out?

Named items are Atlix's sale of an xBUILD 5000 LPBF system to BMW for aluminium parts, Luca Veneri's VECTRON area sintering process, which promises higher speed and lower part cost, and a BQ filament stand that weighs and scans spools. The author's top pick is DWS hybrid SLA, which extrudes material onto a film and then cures a second material with a laser. This allows a very wide viscosity range, conductive and insulating materials in one part, gradients and hard and soft materials.

Why does the author worry about the SnowPod?

The author contrasts the MetalBase, which looks built for safety, with SnowX's SnowPod, citing a stiff chamber seal, a seemingly plastic door and a simple latch. Fires from soot when opening the chamber or in filters are called realistically possible, dust explosions less likely but possible, at roughly 20 to 60 g/m³ in air. The author still supports desktop LPBF as a category but calls for more precaution in consumer settings. These are the author's impressions from a show visit, not test results.

What it means

For small and mid-sized manufacturers, falling prices for depowdering, finishing and consumables lower the entry cost of polymer AM and shift the budget question from the printer to the whole process chain. Impressions from a trade floor are not evidence, though. For low-cost metal systems, the powder handling, ventilation and fire protection obligations of a workshop still apply, and a safety assessment should come before any purchase decision. The Atlix and BMW order continues an earlier AddiWire story.

Earlier on AddiWire

Frequently asked questions

What is DWS hybrid SLA?

According to the report, it extrudes material onto a film, moves the film and cures a second material with a laser. This allows a very wide viscosity range, including conductive and insulating materials in one part.

What concerns were raised about the SnowPod?

The author criticises the chamber seal, the apparently plastic door and a simple latch, and warns of soot fires and possible dust explosions. The author still supports desktop LPBF as a category.

Why are AM entry costs falling?

The author points to cheaper resins and post-processing equipment, partly due to Chinese influence, and to many new peripheral vendors.

Read the original reports
  1. 3DPrint.com, 20 Nov 2026
  2. 3DPrint.com, 20 Nov 2026