AddiWire

Additive manufacturing news and European prices, with independent expert commentary

Industrial AM

EOS HELIOR: three-laser SLS machine aims at 24-hour builds for contract manufacturers

Published 6 sourcesSummary written with AIDeutsche Version

EOS presented HELIOR at Formnext 2026, a large-format polymer SLS system with three lasers, an independently adjustable roller recoater and new exposure software. EOS claims up to 80% higher throughput and up to 80% less depowdering effort, as maximum values for suitable parts. The machine targets service providers who want one full build per day, and it becomes commercially available in December 2026.

Key facts
  • Build volume is 700 × 380 × 580 mm, the same as the EOS P 770
  • Three lasers replace two, with dynamic load balancing between scan fields
  • A full build at 10% packing density completes within 24 hours
  • Commercial availability starts in December 2026 with PA 2200 and PA 2220 HighReuse

Context Depowdering means removing the loose, unsintered powder that surrounds and fills a part after an SLS build, which is often a manual and time-consuming step.

What is new compared with the EOS P 770?

HELIOR keeps the P 770 build volume of 700 × 380 × 580 mm and its exchangeable build-frame concept, but the optics, electrical cabinet and controls are new. The laser beam path is enclosed, and extra airflow around the protection windows is meant to allow six consecutive builds without cleaning. Existing P 770 machines cannot be upgraded to HELIOR.

The machine has three lasers instead of two. Reports differ on their power: one gives 80 W, two others 70 W. Two lasers cover the left and right regions and a third adds capacity in the centre. Software redistributes the scan work layer by layer and shifts the boundaries between scan fields, which is meant to avoid fixed overlap zones running vertically through a part.

How does EOS reach less depowdering effort?

A roller recoater lets EOS set roller rotation independently of travel speed, which produces a softer powder cake. Geometry-aware exposure parameters adjust energy input for bulky areas and thin walls to reduce powder sticking. EOS cites up to 80% less post-processing effort, but the figure refers only to depowdering and to parts with internal channels or slots. Solid parts may see little change, and it is not a universal cut in finishing labour.

The same exposure set is meant to give moving parts the right clearance in one step, instead of two or three beam-offset iterations.

What do the throughput and accuracy claims mean?

EOS designed the machine so that a full-height build at 10% packing density finishes within 24 hours, which it describes as typical for mixed contract jobs. That equals about 154 litres per day and roughly 60% more volume than the P 770 in the same window. The 80% throughput gain is a maximum, not an average. Full builds still need around three days of external cooling, so exchangeable frames are used to keep the machine running.

Two software functions address accuracy: 3D EOSAME compensates temperature variation in the chamber with a machine-specific correction matrix, and Smart Scaling pre-compensates shrinkage in the Z direction. In one example, deviation fell from 740 to 120 micrometres.

Who tested it and what is available at launch?

Five service providers took part in development: FKM Additive Manufacturing, Prototal Group, Materialise, Shapeways and Formrise. Reported productivity gains in their trials were 67% at FKM, 44% at Materialise and 35% at Formrise. Launch materials are PA 2200 and PA 2220 HighReuse, with more to follow on customer demand. Automated alerts from the thermal imaging are still in development. Peripherals such as powder handling and unpacking come with AM Solutions. Detailed cost-per-part data has not been published.

What it means

For European service bureaus, HELIOR is a bet that one predictable build per day matters more than peak speed, and the 10% packing density basis is realistic for mixed jobs. The headline figures are maximums, though, and cooling time, depowdering share and part geometry decide the real gain. Cost per part has not been published, so any business case needs own part data and a quote. Smaller firms should also note that the machine is built for near-continuous operation, and its P 770 base means no upgrade path for existing machines.

Earlier on AddiWire

Frequently asked questions

When can the EOS HELIOR be bought?

EOS announced commercial availability from December 2026. The machine was shown at Formnext 2026 in Frankfurt, Hall 12.0, Booth D71.

Is the 80% throughput gain realistic for every job?

No. EOS describes it as a maximum. Under its reference conditions of 10% packing density and a 24-hour build, it cites about 60% more build volume than the P 770.

Which materials does HELIOR support at launch?

Validated parameters exist for PA 2200 and PA 2220 HighReuse. EOS plans to qualify more materials based on customer requests.

Read the original reports
  1. 3D Printing Industry, 17 Nov 2026
  2. TCT Magazine, 17 Nov 2026
  3. VoxelMatters, 17 Nov 2026
  4. 3DPrint.com, 17 Nov 2026
  5. 3DPrint.com, 17 Nov 2026
  6. 3D Printing Industry, 20 Nov 2026