AddiWire

Additive manufacturing news and European prices, with independent expert commentary

Industrial AM

UK pair WAAM3D and Holdson target qualified wire arc parts and polished metal AM

Published 2 sourcesSummary written with AIDeutsche Version

Two UK firms profiled ahead of Formnext 2026 address different ends of metal AM. WAAM3D, a Cranfield spin-out, reports more aerospace buyers asking for finished, qualified wire arc parts rather than machines. Holdson, founded in 2023, builds electrochemical polishing machines that smooth printed metal surfaces, including internal channels down to about 2 mm.

Key facts
  • WAAM3D nose cone cut material use by 74%, per the company
  • Holdson says 10 to 15 µm Ra falls below 5 µm in about 20 minutes
  • Holdson works with internal channels down to about 2 mm if an electrode fits
  • Accuron Technologies took a majority interest in WAAM3D in December 2023

Context Wire arc additive manufacturing (WAAM) melts metal wire with an electric arc and deposits it along a programmed path, building near-net-shape blanks that are then machined.

Why are aerospace buyers asking WAAM3D for parts, not machines?

WAAM3D was incorporated in 2018 to commercialise wire arc research led by Professor Stewart Williams at Cranfield University. Sales and business development manager Zsolt Pinter says enquiries have shifted toward qualified, ready-to-use parts. Some buyers see little reason to own the deposition equipment.

A reference case is an aluminium wind tunnel nose cone for the Aircraft Research Association, 350 mm long and 190 mm in diameter. WAAM3D deposited metal onto bar stock to make a near-final blank, and ARA machined it. WAAM3D says this cut material use by 74%.

What does the WAAM3D process and qualification picture look like?

The patented GMAX process feeds one energised and one unenergised wire, so heat input can vary while deposition rate stays constant. This matters at intersections, where surrounding metal draws heat away differently. The ShapeTech system maps layer height by measuring distance to the deposited surface, giving engineers locations to inspect after a build. RoboWAAM Plus can accommodate builds up to two metres per axis, with advertised deposition up to 15 kg per hour.

Pinter calls qualification the biggest hurdle for industrialisation at scale. For short orders, a forging lead time of more than a year could drop to two weeks or five days, depending on the part, he said. He did not give a delivery figure for a qualified aerospace component. Accuron Technologies took a majority interest in December 2023, and WAAM3D can now produce parts in Singapore, while research and IP stay in Milton Keynes.

How does Holdson polish printed metal parts?

Holdson, founded in West Yorkshire in 2023, builds Electroform electrochemical polishing machines and offers a small-batch service. The project that started it was with Cummins on turbocharger internal finish. Paul Tickle estimates metal AM is about 60% of the business, mostly aerospace, with Inconel and titanium most common.

The part is the anode in a mainly water-based, salt electrolyte, and metal dissolves preferentially at surface peaks. Tickle says a typical AM part at 10 to 15 µm Ra can drop below 5 µm in around 20 minutes, and some surfaces reach about 1 µm. Removal ranges from a few microns to around 300 µm. Internal channels down to about 2 mm are workable if an electrode can reach them and electrolyte can flow.

What are the process controls, limits and plans?

Holdson uses computational fluid dynamics to map expected removal, then measures Ra after the cycle to update the recipe. The EF-150 takes parts up to 100 mm per side and the EF-300 up to 250 mm. Customers verify with CMM, tensile tests or CT. Tickle suggests accepting a rougher build, 10 to 15 µm Ra, and polishing for 30 to 60 minutes if that saves hours of printer time. His claim of six times faster than competing equipment came without a matched comparison.

Holdson expects double-figure installed machines by end of 2026 and aims to triple that in 2027. Spent electrolyte recycling is targeted for late 2027, with metal recovery planned in 2027. Holdson exhibits at Formnext, Hall 11.0, Stand C52.

What it means

Both profiles point to costs that sit around the printer. For wire arc, buying a finished part moves the qualification burden to a supplier, which can suit smaller manufacturers without deposition cells, though Pinter calls qualification work in progress. For polishing, trading a finer build for a shorter print plus finishing is a per-part calculation that depends on electrode access and allowance, and the speed claims are unverified. Like the earlier UK founder piece on funding and visibility, these are small firms seeking industrial proof.

Earlier on AddiWire

Frequently asked questions

What is WAAM3D's GMAX process?

GMAX feeds an energised and an unenergised wire, so heat input can be varied independently while deposition rate stays constant. This helps on parts with intersecting features.

Can Holdson polish internal channels in metal AM parts?

Yes, down to about 2 mm in diameter, provided an electrode can reach the surface and electrolyte can flow through the passage.

Where does Holdson exhibit at Formnext 2026?

Holdson is in Hall 11.0, Stand C52, in Frankfurt from 17 to 20 November 2026, with an Electroform machine, sample parts and a software station.

Read the original reports
  1. 3D Printing Industry, 16 Nov 2026
  2. 3D Printing Industry, 16 Nov 2026