AddiWire

Additive manufacturing news and European prices, with independent expert commentary

Industrial AM

Wayland Additive: charge control in electron beam printing lets users set build temperature

Published 1 sourceSummary written with AIDeutsche Version

Wayland Additive, based in Huddersfield, built its NeuBeam process to stop charged powder from scattering under an electron beam. According to chief executive Will Richardson, the same step lets the company choose the build temperature of the part separately from the surrounding powder, which matters for crack-prone superalloys, titanium and tungsten. The firm shows the Calibur3 system at Formnext in Frankfurt from 17 to 20 November 2026.

Key facts
  • Founded on 2016 collaboration of Will Richardson and Ian Laidler, Huddersfield
  • Cooling channels as small as 1 mm cleared, per Richardson
  • Beam can sustain 16, 24 or 36 melt pools
  • RAF Typhoon flew with a Calibur3 part in August 2025

Context A smoke event is the sudden scattering of electrically charged metal powder in an electron beam machine, which destroys the level powder layer before melting.

Where does the NeuBeam process come from?

Co-founders Will Richardson and Ian Laidler started working on the topic in 2016. Laidler brought long experience from electron-beam lithography in the semiconductor industry. Their target was the smoke event: electrons charge the powder, which then scatters and ruins the thin layer just spread. Development and venture funding took the team from a prototype to an independent machine builder. The result is NeuBeam, running on the Calibur3 electron-beam powder bed fusion system.

Why does a loose powder bed matter?

Conventional electron-beam machines sinter the whole powder bed into a lightly bonded cake so it stays in place. Operators must hold it between too loose and too hard to break away. With charge neutralised, the powder does not need that sintering, so the part can run hot while the powder around it stays loose.

Richardson names three effects. In crack-prone nickel superalloys such as CM247, a hot build helps while cooling channels as small as 1 mm remain clearable. In titanium, finer, porous supports that break away may be possible, sometimes with a thinner substrate and no separate stress-relief step. Some steels can be built cooler to protect corrosion resistance or to reach hardness straight off the machine, which can remove a heat treatment depending on the specification.

Where does electron beam fit against laser?

Richardson would leave aluminium and thin-walled, lightweight parts that already print reliably to laser systems. His openings are bulky sections that distort, alloys that crack, and long waits for titanium castings. Electron beam asks more of the engineer, who controls part temperature as well as the beam. Building the machine is harder too, as no supplier sells electron beam columns off the shelf.

The beam can also cycle quickly between points to sustain 16, 24 or 36 melt pools at once, keeping small-pool definition while working in parallel. With Fraunhofer IFAM in Dresden, Wayland produced dense, crack-free tungsten demonstrators; fusion energy is seen as a target market.

What is the adoption evidence?

In August 2025 the RAF reported that an operational Typhoon had flown with a replacement metal part made in-house on Calibur3. Richardson put the route to that milestone at under two years, including machine qualification and destructive and non-destructive testing, and expects later programmes to be shorter. He gave no installed-base number, but says early customers now make production parts and reorder machines. A US applications facility is planned. Wayland exhibits at Formnext, Hall 12, Stand B139.

What it means

For manufacturers weighing electron beam against laser, the useful point is that the business case rests on the downstream steps a part still needs: heat treatment, support removal, powder clearing from channels. Benefits depend on alloy and specification, so each part needs its own comparison of total route cost. Qualification is the main timeline factor: the Typhoon example took under two years. Electron beam also demands process knowledge, which matters for smaller firms. This story adds detail to the earlier Formnext preview that listed Wayland's E-PBF showing.

Earlier on AddiWire

Frequently asked questions

What is NeuBeam?

NeuBeam is Wayland Additive's process for neutralising electric charge in the powder bed of its Calibur3 electron-beam machine. It keeps powder from scattering and allows the part temperature to be chosen separately from the powder.

Which materials does Wayland highlight?

Richardson points to high gamma-prime nickel superalloys such as CM247, titanium for casting replacement, and tungsten and other refractory metals. Tungsten demonstrators were made with Fraunhofer IFAM.

Where can visitors see Wayland at Formnext 2026?

Wayland Additive exhibits in Hall 12, Stand B139 at Formnext in Frankfurt, 17 to 20 November 2026.

Read the original reports
  1. 3D Printing Industry, 16 Nov 2026