AddiWire

Additive manufacturing news and European prices, with independent expert commentary

Materials

3devo's X10 extruder turns waste powder into spec-grade filament unattended

Published 1 sourceSummary written with AIDeutsche Version

Dutch maker 3devo has launched the Filament Maker X10, a compact filament extruder for unattended, continuous production from powder, regrind or pellets. It runs at up to 1.5 kg/h with a diameter tolerance of ±30 µm on the spool and is available now through Multistation. 3devo positions it for recycling expensive materials such as MJF and SLS PA12 powder waste.

Key facts
  • Output up to 1.5 kg/h, about five times the Filament Maker TWO
  • Diameter tolerance ±30 µm on the spool
  • Heating up to 450 °C in four zones, ±0.1 °C
  • 3devo recycled over 2,000 kg of MJF PA12 waste in one year

Context Glass transition temperature is the point below which a polymer turns from soft to rigid; extruded filament must cool below it before spooling, which is why cooling length limits the output speed of compact extruders.

What does the Filament Maker X10 do differently?

3devo describes the X10 as a step between its compact lab extruder, the Filament Maker TWO, and full industrial extrusion lines, which need three-phase power, chilled water and a trained operator. The X10 runs on single-phase power, needs no plumbing and is meant for unattended running. It accepts powders, regrind and pellets through a 7.25 L hopper with a vibrating feeder.

The key change is cooling. Filament travels 2.80 m from nozzle to spool on an air-cooled silicone conveyor belt, folded back inside a 1,785 mm long housing. The filament is laid down rather than pulled, which allows 1.5 kg/h, about five times the Filament Maker TWO, according to 3devo.

How is diameter quality kept stable?

A 3-axis optical sensor sits at the end of the cooling path, after the material has finished shrinking. It feeds a fully automatic closed loop that holds the set diameter. 3devo reports ±30 µm on the spool, measured on recycled PA12 with recycled carbon fiber, a harder case than virgin material.

Four independent heating zones reach 450 °C with ±0.1 °C stability, covering PEEK and PEI as well as low-temperature polymers such as PCL and filled or composite compounds. Monitoring works over the local network or the internet. The only manual steps are start, spool change and stop. Custom E3D nozzles and a hardened DC53 tool steel screw target abrasive compounds.

What do the recycling numbers show?

3devo says it collected over 2,000 kg of MJF PA12 powder waste in a year, extruded it on X10 units and printed machine brackets, covers and housings, some with recycled carbon fiber. The company cites 50 to 60 % unused powder per MJF or SLS build and powder prices of 50 to 100 €/kg.

In ISO 527 tests by 3devo, recycled PA12 printed by FDM reached 47 MPa in plane versus 48 MPa for the HP MJF datasheet value. Interlayer adhesion was 23 MPa versus 48 MPa. With 10 % recycled carbon fiber the values were 72 MPa in plane and 51 MPa interlayer. UK supplier Filamentive sells rPA12 filament made from MJF waste on the X10.

What it means

The business case rests on material value: recycling pays where waste is costly, such as PA12 powder or PEEK, and little where virgin PLA costs about 10 €/kg. The strength figures are 3devo's own tests, and the savings example (about 2,000 kg a year, roughly €80,000) is explicitly illustrative. A mid-sized MJF or SLS user should check its own waste volume, requalification effort for parts made from recycled filament, and the anisotropy of FDM compared with powder bed parts before relying on substitution.

Frequently asked questions

How fast and how precise is the Filament Maker X10?

It produces up to 1.5 kg/h with a diameter tolerance of ±30 µm on the spool, measured by 3devo on recycled PA12 with recycled carbon fiber.

Which materials can it process?

Powders, regrind and pellets, with heating up to 450 °C. 3devo lists PEEK, PEI (Ultem), PCL and filled or composite materials.

Where can it be bought?

It is available now through Multistation, according to the announcement.

Read the original reports
  1. Multistation, 19 Nov 2026